How to Install a Bathtub
How to Install a Bathtub
Blog Article
This post in the next paragraphs involving How to Install a Bathtub Yourself is immensely informative. Give it a go and make your own personal ideas.
Setting up a tub isn't precisely brain surgery, yet it does call for strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult project. If the old bathtub is readily accessible, the project can relocate speedily; if you have to open up a wall surface to get rid of the old bathtub and also place the brand-new tub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will certainly require an assistant to leave the old tub and set in the new one. See to it you have actually certified on your own for the task and are comfortable attempting it. As opposed to working with a service provider to take control of a halfway-completed job, it is better to consider employing one prior to you start. Possibilities are you may need a specialist plumber to make tube links.
This short article will help you mount a new bath tub in your washroom if you have already acquired a brand-new tub and do not require to change the setup of your previous water pipes.
Your tools and material list should make up the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you need to do is disconnect the water. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome due to the limited access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel ready for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet ports. The former type ought to be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bath tub
Making use of both wood boards under its feet, put the tub in the required setting. The wood boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following goal is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and adjusting the feet on the bathtub till the level reviews degree.
To set up taps, fit the bottom of the furthest flexible faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water supply and also examine all joints and also new pipework for leaks and tighten them if essential. Fill up the bathtub as well as additionally inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the tub should wait till the tub has been made use of a minimum of once as this will resolve it into its final placement.
Getting ready for the Installation
To start with, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath need to now be ready to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to crack a stiff seal, creating the water to penetrate the wall in between the bathroom and the tiling, resulting in issues with dampness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes and also cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the tub with water prior to securing, to allow for the movement experienced when the tub is in usage. The sealer can fracture fairly early if you do not consider this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy more info about How to Install a Bathtub Yourself? Place feedback down below. We will be glad to know your views about this blog post. In hopes that you come back again in the future. I beg you take the opportunity to share this entry if you enjoyed reading it. Many thanks for taking the time to read it.
Book Appointment
Report this page